reorder
tools-and-supplies.mybogy.online
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New

Bit 12mm Hex 32mm 5/16 Hex Drive

About The KO-KEN 100H..32-12 Bit 12mm Hex 32mm 5/16 Hex Drive

KO-KEN 100H.32-12 Bit 12mm Hex 32mm 5/16 Hex Drive

Hand Tools,Screwdrivers and Nutdrivers,Screwdriver Bits

Bit 12mm Hex 32mm 5/16 Hex Drive

Hand Tools,Screwdrivers and Nutdrivers,Screwdriver Bits

Specifications of Bit 12mm Hex 32mm 5/16 Hex Drive

Category
Instockinstock

Last Updated

Bit 12mm Hex 32mm 5/16 Hex Drive
More Varieties

Rating :- 8.29 /10
Votes :- 1433
1/4-20 x 5 in Phillips Flat Machine Screw, Plain Steel
    • GPS Speedometer, 4 Gauge, White - 60 MPH

    GPS Speedometer, 4 Gauge, White - 60 MPH

    FARIA BEEDE INSTRUMENTS F33839 GPS Speedometer, 4" Gauge, White - 60 MPH.

    • Class A Designer Series RV Cover, Gray, 25

    Class A Designer Series RV Cover, Gray, 25' - 28

    Triple layer SFS AquaShed top panel & triple layer two-tone polypropylene sides; Beads water on contact; Maximum resistance to high humidity & rainfall; Protection against harmful UV rays; Front & rear buckle cinching system; Removes slack; Bottom mounted strap/buckle system; Prevent loss to the wind; Triple layer polypropylene side panels; Insures maximum breathability; Virtually eliminates mold & mildew; Zipper entry panels; Easy access during storage; Weighted tie down assist for easy installation underneath the coach; Water resistant yet breathable; Reinforced front corners resist snags & tears; Moderate climates + short term storage.

    • Our unique flute configuration creates a harmonicsshift, resulting in minimal chatter and an exceptional finish.Premium Sub-Micrograin High-Performance Variable Index Solid Carbide End Mill BitVariable Index GeometryHigher SFM and Heavier Chip LoadsCenter Cutting Carbide EndmillUsed in all slotting, roughing, profiling and finishing applicationsHigh Performance, chatter free machining provides versatility in use for all ferrous materialsDesigned for use in Alloy Steels, Cast Iron, Titanium, Stainless Steel, High Temp andall other ferrous materials up to 50HRcEccentric Relief on the cutting edge provides enhanced edge strengthTHE VI-PRO PERFORMS VERY WELL IN A WIDE RANGE OF MATERIALS INCLUDING: HIGH TEMP ALLOYS, STAINLESS STEELS, ALLOY STEELS, CAST IRON, HIGH TEMP NICKEL BASE ALLOYS, TITANIUM ALLOYS, EXOTICSALCRO-MAX Coating: is mostly suitable when machining tool steel and shows excellent behavior for wet and MQL (minimum quantity lubrication) conditions.

    Our unique flute configuration creates a harmonicsshift, resulting in minimal chatter and an exceptional finish.Premium Sub-Micrograin High-Performance Variable Index Solid Carbide End Mill BitVariable Index GeometryHigher SFM and Heavier Chip LoadsCenter Cutting Carbide EndmillUsed in all slotting, roughing, profiling and finishing applicationsHigh Performance, chatter free machining provides versatility in use for all ferrous materialsDesigned for use in Alloy Steels, Cast Iron, Titanium, Stainless Steel, High Temp andall other ferrous materials up to 50HRcEccentric Relief on the cutting edge provides enhanced edge strengthTHE VI-PRO PERFORMS VERY WELL IN A WIDE RANGE OF MATERIALS INCLUDING: HIGH TEMP ALLOYS, STAINLESS STEELS, ALLOY STEELS, CAST IRON, HIGH TEMP NICKEL BASE ALLOYS, TITANIUM ALLOYS, EXOTICSALCRO-MAX Coating: is mostly suitable when machining tool steel and shows excellent behavior for wet and MQL (minimum quantity lubrication) conditions.

    End Mill TolerancesSize RangeDiameterShank1/8"-1/2"+.1/4 VI Pro Carbide Endmill 5 Flute Stub ALCRO-MAX Coated This coatingis highly recommended for titanium, high temperature alloys, and hardened and tempered tool steels with 35 HRc or greater.

    • Our unique flute configuration creates a harmonicsshift, resulting in minimal chatter and an exceptional finish.Premium Sub-Micrograin High-Performance Variable Index Solid Carbide End Mill BitVariable Index GeometryHigher SFM and Heavier Chip LoadsCenter Cutting Carbide EndmillUsed in all slotting, roughing, profiling and finishing applicationsHigh Performance, chatter free machining provides versatility in use for all ferrous materialsDesigned for use in Alloy Steels, Cast Iron, Titanium, Stainless Steel, High Temp andall other ferrous materials up to 50HRcEccentric Relief on the cutting edge provides enhanced edge strengthTHE VI-PRO PERFORMS VERY WELL IN A WIDE RANGE OF MATERIALS INCLUDING: HIGH TEMP ALLOYS, STAINLESS STEELS, ALLOY STEELS, CAST IRON, HIGH TEMP NICKEL BASE ALLOYS, TITANIUM ALLOYS, EXOTICSALCRO-MAX Coating: is mostly suitable when machining tool steel and shows excellent behavior for wet and MQL (minimum quantity lubrication) conditions.

    Our unique flute configuration creates a harmonicsshift, resulting in minimal chatter and an exceptional finish.Premium Sub-Micrograin High-Performance Variable Index Solid Carbide End Mill BitVariable Index GeometryHigher SFM and Heavier Chip LoadsCenter Cutting Carbide EndmillUsed in all slotting, roughing, profiling and finishing applicationsHigh Performance, chatter free machining provides versatility in use for all ferrous materialsDesigned for use in Alloy Steels, Cast Iron, Titanium, Stainless Steel, High Temp andall other ferrous materials up to 50HRcEccentric Relief on the cutting edge provides enhanced edge strengthTHE VI-PRO PERFORMS VERY WELL IN A WIDE RANGE OF MATERIALS INCLUDING: HIGH TEMP ALLOYS, STAINLESS STEELS, ALLOY STEELS, CAST IRON, HIGH TEMP NICKEL BASE ALLOYS, TITANIUM ALLOYS, EXOTICSALCRO-MAX Coating: is mostly suitable when machining tool steel and shows excellent behavior for wet and MQL (minimum quantity lubrication) conditions.

    0001,-.0001,-..