716 Dia X 716 Shank 60 Deg, Carbide Drill Mill Blue Series

Drill Blank Size Decimal Inch 0104 Drill Blank Size Wire 37 Blank Length Inch 212 Made from hardened HRC 6365 high speed steel and ground, can be used as punches, gauges, pins or ground for special tools High Speed Steel 00000 00003.

Drill Bit Size Letter D Drill Point Angle Degrees 118 Drill Bit Material High Speed Steel Drill Bit FinishCoating Bright Flute Type Spiral Cutting Direction Right Shank Type Straight Coolant Through No Used in shallow hole drilling of aluminum and magnesium alloys and die cast parts Bright finish 118Deg points High Speed Steel.

Operation Type Manual Material S45C Adjustable clamping height.

Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 12 Projection Decimal Inch 354 Nose Diameter Decimal Inch 106 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market.

20mm Diameter 3-Flute Ball Nose Regular Length TiAlN Coated Carbide End Mill 3 flute carbide end mills offer maximum chip clearance therefore reducing chip packing..

Mill Diameter Inch 14 Number of Flutes 2 Material High Speed Steel Length of Cut Inch 12 Shank Diameter Inch 38 FinishCoating Bright Single or Double End Single Center Cutting Yes Overall Length Inch 2516 Flute Direction Right Cutting Direction Right Variable Helix No Helix Angle 30 These end mills are furnished as regular with righthand cutting and righthand helical flutes All shanks are flatted for holder set screw Designed for slotting, drilling, pocketing and generalpurpose operation 2 helical flutes Centre cutting Single end with weldon shank Keyway tolerance.

Material Solid Carbide Mill Diameter Inch 716 Shank Diameter Inch 716 Length of Cut Inch 1 Point Angle 60 Number of Flutes 2 FinishCoating Bright DrillMills can be used for drilling, slotting, and profile milling 2 Flute 60Deg 90Deg included point angle Made from submicron grain carbide Cutting diameter tolerance 00000002.

Drill Blank Size Inch 5964 Drill Blank Size Decimal Inch 09219 Blank Length Inch 6 Made from hardened HRC 6365 high speed steel and ground, can be used as punches, gauges, pins or ground for special tools High Speed Steel 00000 00005.

Material Solid Carbide Mill Diameter Inch 716 Shank Diameter Inch 716 Length of Cut Inch 1 Point Angle 60 Number of Flutes 2 FinishCoating Bright DrillMills can be used for drilling, slotting, and profile milling 2 Flute 60Deg 90Deg included point angle Made from submicron grain carbide Cutting diameter tolerance 00000002.

Drill Blank Size Inch 5964 Drill Blank Size Decimal Inch 09219 Blank Length Inch 6 Made from hardened HRC 6365 high speed steel and ground, can be used as punches, gauges, pins or ground for special tools High Speed Steel 00000 00005.